5/8-Port 10/100/1000MbpsIndustrial Gigabit Ethernet SwitchIGS-501 / IGS-801 / IGS-501T / IGS-801TUser's Manual
102. INSTALLATIONThis section describes the functionalities of the Industrial Gigabit Ethernet Switch’s components and guides how to in
112.1.1 Product OverviewThe PLANET Industrial Gigabit Ethernet Switch with 5/8 RJ-45 10/100/1000Mbps ports for high-speed network connect
12Figure 2-3 IGS-501T front panel Figure 2-4 IGS-801T front panel2.1.3 LED IndicatorsLED Color FunctionP1 Green Lit: indicate the
132.1.4 Switch Upper PanelThe upper panel of the Industrial Gigabit Ethernet Switch consist one terminal block connector within two DC power
142. Tighten the wire-clamp screws for preventing the wires from loosing.1 2 3 4 5 6Power 1 Fault Power 2- + - +NoteThe wire gauge for the termin
152.2 Mounting InstallationThis section describes how to install the Industrial Gigabit Ethernet Switch and make connections to it. Please re
16Step 1: screw the DIN-Rail on the Industrial Gigabit Ethernet Switch.Step 2: Lightly press the button of DIN-Rail into the track.Step 3: Check th
17Step 5: Lightly press the button of DIN-Rail for remove it from the track.2.2.2 Wall Mount Plate MountingTo install the Industrial Gi
183. APPLICAITONIn this paragraph, we will describe how to install Industrial Gigabit Ethernet Switch and the installation points for the at
19Step 3: To hang the Industrial Gigabit Ethernet Switch on the DIN-Rail track or wall, please refer to the Mounting Installation s
TrademarksCopyright © PLANET Technology Corp. 2009.Contents subject to revision without prior notice.PLANET is a registered trademark of PLANET Techno
204. SWITCH OPERATION4.1 Address TableThe Industrial Gigabit Ethernet Switch is implemented with an address table. This address table compose
214.4 Store-and-ForwardStore-and-Forward is one type of packet-forwarding techniques. A Store-and Forward Industrial Gigabit Ethernet Swit
225. TROUBLESHOOTINGThis chapter contains information to help you solve issues. If the Industrial Gigabit Ethernet Switch is not funct
23APPENDIX A: NETWORKING CONNECTIONA.1 Switch’s RJ-45 Pin Assignments1000Mbps, 1000Base-TContact MDI MDI-X1 BI_DA+ BI_DB+2 BI_DA- BI_DB-3 BI_DB+ BI_DA
24A.2 RJ-45 cable Pin AssignmentsThe standard RJ-45 receptacle/connectorThere are 8 wires on a standard UTP/STP cable and each wire is color-coded. Th
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user wi
Table Of Contents1. INTRODUCTION ... 6 1.1 Package Contents ...
4.5 Auto-Negotiation ...215. TROUBLESHOOTING ...
61. INTRODUCTION1.1 Package ContentsCheck the contents of your package for following parts:Industrial Gigabit Ethernet Switch x 1User's manual x
71.3 Product FeaturesPhysical Port5-Port 10/100/1000Base-T RJ-45 with auto MDI/MDI-X function (IGS-501 / IGS-501T)8-Port 10/100/1000Base-T RJ-45 with
81.4 Product SpecicationsModel IGS-501 IGS-801Hardware Specication 10/100/1000Base-T Ports 5 8Dimensions (W x D x H) 135mm x 87mm x 32mmWeight 455
9Model IGS-501T IGS-801THardware Specication 10/100/1000Base-T Ports 5 8Dimensions (W x D x H) 135mm x 87mm x 32mmWeight 455g 473gPower Requiremen
Comentarios a estos manuales