Planet Technology WAP5 Manual de usuario

802.11b WLAN Outdoor AP WAP-5000 User’s Manual

- 6 - corrosion-resistant connectors. l Refer to the National Electrical Code for grounding details. IF A PERSON COMES IN CONTACT WITH ELECTRICAL POW

- 7 - Chapter 3 PLANET Outdoor WLAN Management System 3.1 Introduction The bundled PLANET Outdoor WMS (WLAN Management System) is a powerful u

- 8 - 3. You can click “Browse” to specify the Destination Folder that you want to install the utility. Or you can keep the default setting and clic

- 9 - 4. Click “Next” to continue. 5. The setup will start to copy necessary files to your computer. When the Setup Complete window appears, click “

- 10 - 3.3 Using PLANET Outdoor WMS After successfully installing the utility, you can found the icon on your desktop. To activate WMS, you can d

- 11 - 3.3.1 Kick Start It is recommended to use Kick Start function when initial setting up a WAP-5000. Open Start menu and select Kick Start, or c

- 12 - 3.3.1.1 Find This function helps you to quickly locate all compatible devices (include AP and Bridge). Open the Start menu and select Find, or

- 13 - MAC address of the device and click OK to make the connection. 3.3.1.4 Delete If you want to remove a specific device from the list, select i

- 14 - 3.3.1.8 Change Password This function allows you to change the administrative password of the device. Highlight the MAC address of a device fr

- 15 - 3.3.2.1 Auto Discovery This function helps you to quickly locate all compatible devices in the same IP subnet as the administrative PC. Open

Copyright Copyright 2004 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, s

- 16 - • Device Name: WMS system default category name • Name: Device name assigned by the user for easier identification • S/W Version: Shows the de

- 17 - 3.3.2.3 Config This function allows you to configure the parameters of WAP-5000. Open the Host menu and select Config, or click on the icon ,

- 18 - • NetBEUI Protocol • AppleTalk Protocol • Other Protocols • Internet Multicast Frames SNMP Access Control WAP-5000 contains an SNMP access ta

- 19 - When you select SNMP Access Control, the system will display four blank fields for setting (maximum of 4 SNMP devices can be set). Right-cli

- 20 - To add a wireless station to the list, click on the icon and a dialog box will pop up. Type in the MAC address of the wireless station and

- 21 - • Name: Assigns the WAP-5000 a unique name that allows the AP to be easily identified on the network. • SSID: The SSID is the name shared amo

- 22 - There are four selectable options in Method pull-down menu: • WEP: Disable, Authentication: Open – Disable data encryption • WEP: Enable, Aut

- 23 - view and save the event logs from the station as a Trap Server. To assign a trap server, click Trap Server tab. Click the icon and assign

- 24 - IEEE 802.1X The IEEE 802.1X window allows you to set up 802.1x authentication on a WAP-5000. Check Enable 802.1X Access Control box will acti

- 25 - • Supplicant Timeout – This control sets the maximum time that the AP will wait for an authentication response from a client. Once this limit

Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled

- 26 - • Retries – This is the number of times the AP will attempt to resend accounting information to the server before returning an error. • Enabl

- 27 - • Server IP – This is the RADIUS server’s IP address. This must be set in order for the AP to communicate with the server. • Authentication P

- 28 - A configuration file can also be imported to recover the WAP-5000’s original settings. This profile can also be copied to the other WAP-5000.

- 29 - The configuration profile does not contain the security key settings. The attributes of security keys are externally write-only and cannot be

- 30 - 3.3.2.4 Restart You can restart a selected WAP-5000 by opening the Host menu and select Restart, or click on the icon . A warning message wi

- 31 - 3.3.2.7 New/Edit/Delete Host Address Click the icon to open the New/Edit Address dialog box. After enter the IP address of a WAP-5000, WMS

- 32 - 3.3.3 Trap View If the administrative PC has been assigned as a Trap Server of a WAP-5000, you can use Trap View to view the trap log informat

Chapter 4 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the WAP-5000. How d

TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...1 1.1 PACKA

- 1 - Chapter 1 Introduction WAP-5000 is an IEEE 802.11b Wireless Outdoor Access Point. The special designed housing allows WAP-5000 to be installed

- 2 - 1.3 Features • Wireless LAN IEEE802.11b compliant • Solid housing provides protection against rigorous weather conditions • Strong network sec

- 3 - Storage temperature: -30 – 80 degree C Relative humanity: 5% – 95% (non-condensing) Power Requirement 12V DC, 2.0A Electromagnetic Compatibili

- 4 - Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WAP-5000.

- 5 - OUTDOOR INSTALLATION WARNING IMPORTANT SAFETY PRECAUTIONS: LIVES MAY BE AT RISK! Carefully observe these instructions and any special instruct