Planet-technology ADSL 2/2+ Router with USB Port ADE-3410v2 Manual de usuario

ADSL 2/2+ Router with USB Port ADE-3410v2 User's Manual

3. 64 MB RAM minimum 4. 20 MB of free disk space minimum 5. Ethernet Network Interface Card 2.2 Hardware Installation This section describes how

USB Installation To connect the DSL router to the PC’s USB port, perform the following: z Connect the USB cable to the USB port on the DSL router. T

2.4 Factory Reset Button The Router may be reset to the original factory default settings by depressing the reset button for a few seconds while

the windows will search CD-Rom for the best USB driver. . The dialog prompted you to choose your search and installation options. You can choos

Click the button<Finish> to complete the USB driver installation. 3. Introduction to WEB Configuration 3.1 Quick Setup The Qui

ADE-3410V2 also supports pass-through PPPoE sessions from the LAN side while simultaneously running a PPPoE client fro non-PPPoE LAN devices. NAPT an

STEP 4: Click Next to display the following screen. Choosing different connection types pops up different settings requests. Enter appropriate setting

using the LAN interface IP address. The ADSL router extends the IP subnet at the remote service provider to the LAN PC. That is, the PC becomes a host

5. After clicking Save/Reboot, the router will save the configuration to the flash memory, and reboot. The Web UI will not respond until the system i

After logging in the ROUTER by a super username, you can query, configure, and modify all configurations of the ROUTER; and you can diagnose the ROU

Copyright Copyright© 2007 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed,

This interface contains the following information: Board ID: Software Version: Bootloader (CFE) Version: Upstream Line Rate/Downstre

3.4.3 Statistics -- LAN Click “Statistics”-->”LAN” to show the following interface. You can query information on packets received at the Eth

3.4.5 Statistics -- ATM Click “Statistics”-->”ATM” to show the following interface. You can query information on packets received at the ATM

You will see the following information pertinent to the ADSL line in the page: Mode: G.DMT/G.LITE/T1.413/ADSL 2+/ADSL 2/READSL2 Line Coding:

3.4.8 ARP Click “ARP” to show the following interface. You can query the MAC and IP addresses information of the equipment attached to the ROUTER

3.5 Advanced Setup Click “Advanced Setup” to enter the advanced system setup interface. By default, there are two options at the left side of t

Choose Add, Edit, or Remove to configure WAN interfaces. Choose Save/Reboot to apply the changes and reboot the system. Now we only show you how t

PPP Username: the correct user name that your ISP has provided to you. PPP Password: the correct password that your ISP has provided to you.

Multicast, WAN Service. IGMP Multicast: IGMP proxy. For example, if you need PPPoE mode support IPTV, please enable it. WAN Service: Please en

modifications. NOTE: You need to reboot to activate this WAN interface and further configure services over this interface. 3.5.1.2 Configure PPP

R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF

Click “Next”. In this interface, you can modify the PPP Username, PPP Password, Authentication Method and so on. PPP Username: the correct user

In this interface, you can modify the Service name and enable/disable the IGMP Multicast, WAN Service. IGMP Multicast: IGMP proxy. For example, if

Click “Next”. In this interface, you can modify the WAN IP address, Default Gateway and DNS Server settings. Obtain an IP address automatically

After correctly modifications, click “Next” to show the following interface. In this interface, you can modify the Service name and enable/disabl

Click “Next”. In this interface, you can modify the WAN IP, Default Gateway and DNS Server settings. WAN IP Address: Input the IP address of t

IGMP Multicast, WAN Service. Enable NAT: Select it to enable the NAT functions of the ROUTER. If you are not to enable NAT and intend the user of t

Click “Next”. In this interface, you can modify the Service name. WAN Service: Please enable it, unless you don’t need to active the PVC. C

Enable IGMP Snooping: It used to Bridge mode. 3.5.3 NAT Click “NAT” to show the following interface. Under “NAT”, there are four network

When NAT is enabled on the ROUTER, the whole LAN that the ROUTER is attached will appear as a single machine on the Internet. Normally, external users

Service Name: Select one service item, such as Mail (SMTP), Mail (POP3), Web Server (HTTP), FTP Server, and TFTP, from the list. The information about

4Table of Contents 1. Introduction... 6 1.1 Featur

A maximum 32 entries can be configured. 3.5.3.3 NAT -- DMZ Host Click “DMZ Host” to pop up an interface as below. In this interface, you can

3.5.4 Security Click “Security” -->” IP Filtering” to show the following interface. By default, the firewall is enabled. The firewall is used to

3.5.4.2 Incoming IP Filtering Setup Click “Security”-->” IP Filtering”-->” Incoming” to show the following interface. By default, all i

3.5.4.3 Parental Control Click “Security”-->”Parental Control” to show the following interface. Click “add” to show the interface. This

Click “ENABLE Automatic Assigned Default Gateway” box to show the interface. 3.5.5.2 Routing – Static Route In this interface, you can modify

3.5.6 DNS 3.5.6.1 DNS Server In this interface, you can modify the DNS server settings. If 'Enable Automatic Assigned DNS' checkbox

Click “Add” to add dynamic DDNS. 3.5.7 DSL In this interface, you can modify the DSL settings. Select one you need. But the default sett

3.6 Diagnostics Click “Diagnostics” to show the interface. Your router is capable of testing your DSL connection. The individual tests are listed

3.7.1.2 Settings Update Click the “Browsing...” button, select the correct update configure settings file. Then click the “Update Settings” to

Click “Restore Default Settings” to restore DSL router settings to the factory defaults. 3.7.2 System Log Click “System Log” to show the fol

3.5.2 LAN... 36 3.5.3 NAT...

If you select “Remote” or “Both”, all events will be transmitted to the specified UDP port of the specified log server. After operations under

you can enable/disable the HTTP, ICMP, SNMP, TELNET and TFTP services. And the LAN side and WAN side can have different configurations. 3.7.4.2

management station permitted to access the local management services, and click “Save/Apply”. 3.7.4.3 Access Control – Passwords Click “Access

before the reboot is over. You must guarantee the update software is right and accurate. It is strictly forbidden to use other software for updates.

. Descriptions In this example, the ROUTER is connected to the DSLAM through PVC 8/35 and the access mode is the built-in PPPOA+NAT. The encapsula

You can also modify the PVC 8/35. If you need to modify the LAN IP address and DHCP server information, you can do it in “LAN” in “Advanced Setup”.

3. In the “ATM PVC Configuration” interface configure VPI/VCI as 8/35 and then click “Next”. 4. In the “Connection Type” interface, select “PPP over

address of the ROUTER is automatically obtained through DHCP; the PC attached to the ROUTER is assigned with a private IP address (within the same seg

If “Enable NAT” is disabled during the configuration, you must configure the route on the BRAS; otherwise you cannot access your ISP. In applicatio

“LLC/SNAP-ROUTING” as the encapsulation, and then click “Next”. 5. In the “WAN Settings” interface, input the IP address, subnet mask, and DNS ser

1. Introduction The PLANET ADSL 2/2+ Router, ADE-3410v2, provides office and residential users the ideal solution for sharing a high-speed ADSL 2/2

10.28.108.1. Setting 1. Activate your browser and input “192.168.1.1” in the address column to login the ROUTER. 2. Click “Advanced Setup” ->

by BRAS through its built-in PPPOE dial-up. The ROUTER will assign this public IP address to the PC (configured as “Obtain an IP address automatically

622. Question: Why LINK/ACT LED is not lighting? Answer: • Check the connection between the ADSL router and your computer or Hub/Switch. • Che

 VPN Pass through Support PCs with VPN (Virtual Private Networking) software using PPTP, L2TP, and IPSec are transparently supported - no configurati

LED Indicator LED Meaning 1 PWR Lit when power is ON. 2 Link Lit when DSL line is connected. Blink when DSL line is training. 3 Data Blink w

Rear panel Port and Button Definition Port Meaning 1 Power Switch Power ON/OFF switch 2 Power Connect the supplied power adapter to this j