Planet Technology POE-1200 Manual de usuario

User’s Manual POE-1200 POE-

7 Figure 2-4 POE-2400 Rear Panel Power Notice: 1. The device is a power-required device, it means, it will not work till it is powered. If your ne

8 Step5: Supply power to the PoE Injector Hub. A. Connect one end of the power cable to the PoE Injector Hub. B. Connect the power plug of the powe

9 Figure 2-6 Mounting thePoE Injector Hub in a Rack Step6: Proceeds with the steps 4 and steps 5 of session 2.2.1 Desktop Installation to connect t

10 Figure 2-7 Network application installation The PoE Injector Hub supports Data passive mode, that is, even the PoE Injector Hub is manual power

11 3 MANAGEMENT This chapter describes how to manage the Web Smart PoE Injector Hub. Topics include: - Overview - Management method - Logging on to

12 Figure 3-1 Web Management over Ethernet 2. When the following login screen appears, please enter the default username "admin" and pass

13 3.3.2 PLANET Smart Discovery Utility For easily list the PoE Injector Hub in your Ethernet environment, the Planet Smart Discovery Utility from us

14 4. This utility show all necessary information from the devices, such as MAC Address, Device Name, firmware version, Device IP Subnet address, al

15 4 WEB CONFIGURATION The PoE Injector Hub provide Web interface for PoE smart function configuration and make the PoE Injector Hub operate more eff

16 4.2 Web Panel At the top of the Web management page, the active panel displays the link status of management port and PoE ports. Figure 4-2 Main

2 Trademarks Copyright © PLANET Technology Corp. 2008. Contents subject to which revision without prior notice. PLANET is a registered trademark of P

17 4.3.1 System Information The System information allows viewing system MAC Address, Software Version, Hardware Version, IP Address, Subnet Mask and

18 The page includes the following configurable data: Object Description Choose what the PoE Injector Hub should do following power-up: transmit a

19 4.4 PoE  Power Management: In a power over Ethernet system, operating power is applied from a power source (PSU-power supply unit) over the LAN

20 PoE Function Can enable or disable the PoE function. Priority Set port priority for the POE power management It can choose the “port priority”,

21 4.5 Tools This function displays the PoE Injector Hub tools; include “System Reboot”, “Configuration Setting”, “Alert trap Configuration” and “Fir

22 4.5.2 Configuration Setting This function allows backup and restore the current configuration of PoE Injector Hub, or reset the converter to facto

23 Restore The PoE Injector Hub will restore to previous backup/saved configuration while the “Restore” button be pressed. And please note that on

24 4.5.3 Alert Trap Configuration This function displays the PoE Injector Hub alert trap configuration; include “enable” or “disable” the trap mode a

25 4.5.4 Firmware Upgrade This section provides firmware upgrade of PoE Injector Hub, after choose this function and the following screen appears in

26 Figure 4-19 Firmware Upgrade screen Do not power off the PoE Injector Hub until the update progress is complete. Do not quit the Firmware Upg

3 TABLE OF CONTENTS 1. INTRODUCTION...

27 Figure 4-21 Login screen

28 5. POWER OVER ETHERNET OVERVIEW What is PoE? Based on the global standard IEEE 802.3af, PoE is a technology for wired Ethernet, the most widely in

29 The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to the center tap of the isol

30 6. THE POE PROVISION PROCESS While adding PoE support to networked devices is relatively painless, it should be realized that power cannot simply

31 6.3 Start-up Once line detection and optional classification stages are completed, the PSE must switch from low voltage to its full voltage capaci

32 7 TROUBLESHOOTING This chapter contains information to help you solve problems. If the Device is not functioning properly, make sure the Ethernet

33 APPENDIX A A.1 MDI Settings The Medium-Dependant Interface (MDI or RJ-45) serves as the data/power interface between Ethernet elements. As such, i

34 A.3 DATA OUT PoE Injector RJ-45 Port Pin Assignments PIN NO RJ-45 SIGNAL ASSIGNMENT 1 Output Transmit Data + 2 Output Transmit Data - 3 Receiv

35 Before you powered PD, please check the RJ-45 connector pin assignment follow IEEE 802.3af standard, otherwise you may need change one of the RJ-4

36 APPENDIX B B.1 Power over Ethernet Compatibility test No. PDs PoE Output Note 1 [PLANET POE-151S-12V] + [PLANET ICA-500] 9.6W 2 [PLANET PO

1 1. INTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: ● IEEE 802.3af Power over Ethernet Injector Hub x1 ●

PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw 11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. T

PLANET TECHNOLOGY CORPORATION e-mail: [email protected] http://www.planet.com.tw 11F, No. 96, Min Chuan Road, Hsin Tien, Taipei, Taiwan, R.O.C. T

2 Figure 1-1 Power over Ethernet Application 1.3 How to Use This Manual This Web Smart Power over Ethernet Injector Hub User Manual is structure

3 1.4 Product Features  Interface  24 / 48-Port RJ-45 STP ¾ 12 / 24-Port “Data input” ¾ 12 / 24-Port “Data + Power output”  1 10/100Base-TX Ma

4 1.5 Product Specifications Product POE-1200 POE-2400Hardware Specification“Data” Input Ports12 x RJ-45 STP 24 x RJ-45 STP “Data+Power” Output Po

5 2. INSTALLATION This section describes the hardware features and installation of these PoE Injector Hub on the desktop or rack mount. For easier m

6 The following is the summary table of Reset button functions: Reset Button Pressed and Released Function About 1 second Reboot the PoE Injector H