Planet Technology FPS-1010G Manual de usuario

802.11g USB2.0 Print Server FPS-1010G User’s Manual

1.4.3 Network Printing Functions for Network Server Windows NT ServerNetWare ServerWindows 98Windows NTWorkstationWindows 2000UnixPrint ServerNetw

Network printing function will become available after PTPP driver is installed into Windows NT/2000. Adding this printing function into Windows NT/200

Chapter 6. UNIX System Network You may select the appropriate chapters and sections to read depending on your network printing’s requirement. Chapter

Chapter2 Hardware Installation 1. Make sure the power is OFF, then connect printer to the Print Server's printer port. 2. Connect the LAN cab

Chapter3 Windows Peer-to-Peer Network 3.1 System Architecture Print server supports Windows Peer-to-Peer network printing mode, which is suitable

2. Click on “Administrator Installation” hyper link to initiate the installation. Or you can click the “Start” button and choose “Run”. (Suppose “E”

5. Specify the program folder name where the program icons will be add to. Please click “Next” to start installation. 6. For a while, the program

7. “Name the print Server”, you can assign an easy to memorize name for management. But note that, this name will be the “Identifier” for the Peer-t

NOTE: If this is the first time you configure the print server, the “Print Server Name” will be the same as the “Device Name” printed at the bottom of

10. The “Setup complete” window is displayed to indicate that the Administrator Installation procedure is finished. Please click “Finish”. After t

Copyright (C) 2005 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed products of PLA

Now, you have completed the administrator’s setup for most of the network environment. You can then perform the “Client Installation” procedure (secti

Step5. Choose the “Print Server’s Network Port” which was created by the administrator installation process and click “Next”. Step6. Complet

2. Remote Ports Remote Ports Utility offers a convenient way for you to manage and add printer port of the remote FPS-1010G. From the assistant of thi

4. Uninstall Assistant for removing all installed administrator software. 3.4 Client Installation and Setup The Client Installation can be perfor

Chapter4 Windows NT/2000 Network 4.1 System Architecture In Windows network environment, other than the Peer-to-Peer network printing architecture

If this is your first time installing print server, please install the administrator software on Windows NT/2000 server first. Refer to section 3.2 fo

Chapter5 NetWare Network 5.1 System Architecture We implement NetWare print sharing functionality into the print server itself, thus allowing one

1. Run NetWare’s PCONSOLE program to create a NetWare print server and print queue with the appropriate names. 2. Refer to section 7.7 and use print

9. Press Enter to select the newly created print server. 10. Select Print Server Configuration. 11. Select Printer Configuration. 12. Select Print

Chapter6 UNIX System Network 6.1 Introduction The print server is available for TCP/IP printing by Unix LPD (Line Printer Daemon) protocol. The

Table of Contents CHAPTER1 INTRODUCTION... 5 1.1 Product Introduction...

recommend that the BOOTP server should be located on the same subnet as the print server. If you use Network Information Services (NIS) in your system

6.5 Configure Remote LPD Printing on the Host The procedure you use to configure your Unix host(s) to allow printing to your network remote print

The rm= entry should correspond to the IP address you have assigned to the print server. You can also use a host name if you have assigned one in the

Chapter7 Configuration Utility 7.1 Introduction This chapter introduces FPS-1010G system configuration utility in Windows environment. This utilit

7.2 Search for All Available Print Server Every time when you run print server’s configuration utility, click the “Search” icon on the tool bar

7.3 Status of Print Server Click “Status” icon on the tool bar, the status of the current selected print server will be showed on the right side

7.4 Setting up the Print Server Click “Setup” icon on the tool bar, the setup items of the current selected print server will be showed on the

7.5 General Configuration Double Click “General” icon and the General configuration window will pop-up. You can see basic print server informat

7.6 TCP/IP Configuration Double Click “TCP/IP” icon and the TCP/IP configuration window will pop-up. If there is a DHCP Server in your LAN. You

7.7 Netware Configuration Double Click “NetWare” icon and the NetWare configuration window will pop-up. This print server supports NetWare Binde

7.10.2 Ad-Hoc Mode ...4

7.8 AppleTalk Configuration Double Click “AppleTalk” icon and the AppleTalk configuration window will pop-up. AppleTalk is a data communication

7.9 System Configuration Double Click “System” icon and the System configuration window will pop-up. In the System configuration page, you can s

7.10 Wireless Due to wireless interface is “Disable” in default. If you want to use the print server through wireless interface, please set up the

2. When you are select first option to continue, you will see this screen for scan the wireless network. Please select the wireless device that you

If you want to use WPA-PSK, you have to select “WPA-shared key”. The wireless security setting should be the same with other wireless devices in the s

You can select “64 bit” or “128 bit” length and “Hexdecimal” or “ASCII” format for the encryption key. Longer key length can provide stronger securit

WPA-shared key Security Mode: When “WPA-shared key”, also named “WPA-PSK” requires users to select the advanced encryption methods, i.e. TKIP and ent

4. You can select to let the print server automatically obtain IP settings from DHCP Server or manually assign the IP settings. If you manually assig

7.10.2 Ad-Hoc Mode 1. If you are select “Ad-Hoc Mode” and click “Next” in section 7.11, you will see the dialog box below. You can let the print se

3. This print server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “

Chapter1 Introduction 1.1 Product Introduction Thank you for purchasing and using our FPS-1010G. This print server allows your printer to become

You can select “64 bit” or “128 bit” length and “Hexdecimal” or “ASCII” format for the encryption key. Longer key length can provide stronger securit

When “WPA-shared key”, also named “WPA-PSK” requires users to select the advanced encryption methods, i.e. TKIP and enter a set of shared key.  WPA

5. Please click “Save” to save the wireless configuration. 7.11 SNMP Double Click “SNMP” icon and the SNMP configuration window will pop up.

7.12 Wizard Click “Wizard” icon on the tool bar, the setup wizard item of the current selected print server will be showed on the right side of t

Step 1: Setup the Print Server Name and SMB Group Name of this print server and the name of each printer port. Please refer to section 7.5 and 7.9 fo

Step 3: Setup the IP of this print server. Please refer to section 7.6 for detail information. Step 4: Setup the NetWare printing. Please refer to

Step 5: Setup the AppleTalk printing. Please refer to section 7.8 for detail information. Step 6. Setup Status Summary. This screen will show you

Step 10. Please press “Yes” to save the settings.

7.13 Report Click “Report” icon on the tool bar, the Report window will pop-up. The report list basic information of all available print servers

Chapter8 Web Management 8.1 Introduction Print server can be configured and managed on the web browser. Through Local Area Network, or even Intern

Right View Left View Top View LED Status Description WLAN On: Indicates wireless interface is enable. Off: Indicates wireless interface is disa

8.3 Device Status 8.3.1 System In this page, it will show you all the system information such as “Device Name”, “Print Server Name”, “Model

8.3.3 TCP/IP This page lists all TCP/IP Settings, include “IP Address”, “Subnet Mask” and “Gateway”. 8.3.4 SMB This page will show the

8.3.5 SNMP This page will show the SNMP System Contact and SNMP System Location. If the settings are empty, this page will show you the settings

8.3.7 AppleTalk This page lists AppleTalk settings, include “AppleTalk Zone Name” and “Printer Type of printers connected to all print ports”.

Port Name: The name of the printer port. Each printer port has to be assigned a name. The printserver driver uses this name to access the printer port

network by Ethernet cable when starting up, the print server will run in Ethernet mode. If the print server is not connected to an active network by E

8.4.2.2 Encryption This print server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you

 Key Format - You may select to use ASCII Characters (alphanumeric format) or Hexadecimal digits (in the "A-F", "a-f" and "

 WPA Key – Enter 8 to 63 digits of ASCII format to be the key for the authentication within the network. When you finish configuring the wireless s

8.4.3 TCP/IP You can configure the print server to automatically obtain an IP addddress from your LAN DHCP server or manually specify a static IP add

Print Server Client User Network Server (optional) Windows NT ServerNetWare ServerWindows 98Windows NTWorkstationWindows 2000Unix Print ServerNetwork

8.4.5 SNMP This printserver has support SNMP protocol for users use SNMP management tool to monitor from a remote site. You can Enable this proto

name, print server polling interval and the name of queue on the NetWare server for each printer port. Polling Time: The polling interval of the print

8.5 System Tools 8.5.1 Load Default You can restore print server to factory default settings in this screen. All of your previous configurat

Chapter9 IPP Printing 9.1 Introduction IPP (Internet Printing Protocol) Printing provides a convenient way of remote printing service by TCP/IP. The

“http://192.168.12.13/lpt1:631”. After entering the URL of print server, click “Next >” and complete the configurations afterwards to access the sh

Appendix A Specification Model FPS-1010G Wired Interface Media Interface 1-port RJ-45 UTP Standards IEEE802.3, 10Base-T; IEEE802.3u, 100Base-TX Ca

1.4.2 Network Printing Functions for Clients Windows NT ServerNetWare ServerWindows 98Windows NTWorkstationWindows 2000UnixPrint ServerClient Us

In the client installation procedure, after PTPP (Peer-to-Peer Printing Driver) is installed into Windows, the system will automatically (manual conf