Planet Technology IAD-200W Manual de usuario

ADSL 2/2+ VoIP Router IAD-200, IAD-200W User's Manual

Package Contents The following items should be included. If any of these items are damaged or missing, please contact your dealer immediately. • The

Connection Status - PPPoE & PPPoA If using PPPoE (PPP over Ethernet) or PPPoA (PPP over ATM), a screen like the following example will be display

Connection Details - Dynamic IP Address If your access method is "Direct" (no login), with a Dynamic IP address, a screen like the followin

IAD-200 / IAD-200W, clicking the "Renew" button will attempt to re-establish the connection and obtain an IP Address from the ISP's DH

Connection Details - Fixed IP Address If your access method is "Direct" (no login), with a fixed IP address, a screen like the follow-ing e

Using VoIP VoIP cannot be used until configuration has been completed. See the VoIP topic in Chapter 5 - Advanced Features for details of VoIP config

A Appendix A Troubleshooting This Appendix covers the most likely problems and their solutions. Overview This section covers some common problems tha

Problem 2: Some applications do not run properly when using the IAD-200 / IAD-200W. Solution 2: The IAD-200 / IAD-200W processes the data passing thr

stations. This will mean high access speed is only possible when close to the IAD-200W. 101

B Appendix B About Wireless LANs (IAD-200W only) This Appendix provides some background information about using Wireless LANs (IAD-200W only). Modes

Channels The Wireless Channel sets the radio frequency used for communication. • Access Points use a fixed Channel. You can select the Channel used

Physical Details Front-mounted LEDs IAD-200 IAD-200W Figure 2: Front Panel Power LED (Green) On - Power on. Off - No power. Status LED (Yellow) Of

Wireless LAN Configuration To allow Wireless Stations to use the Access Point, the Wireless Stations and the Access Point must use the same settings,

105

Internet On - Internet connection is available. Off - No Internet connection available. Flashing - Data is being transmitted or received. 6

Rear Panel IAD-200 IAD-200W Figure 3: Rear Panel ADSL port Connect this port to your ADSL line. PSTN Connect this to your PSTN line (normal analog

Chapter 2 Installation This Chapter covers the physical installation of the ADSL 2/2+ VoIP router (IAD-200) / 802.11g ADSL 2/2+ VoIP router (IAD-200W

2. Connect LAN Cable Use the supplied LAN cable to connect the LAN port on the IAD-200 / IAD-200W to your hub. 3. Connect ADSL Cable Connect the supp

Chapter 3 Setup This Chapter provides Setup details of the IAD-200 / IAD-200W. Overview This chapter describes the setup procedure for: • Internet A

Configuration Program The IAD-200 / IAD-200W contains an HTTP server. This enables you to connect to it, and configure it, using your Web Browser. Yo

If you cannot connect If the IAD-200 / IAD-200W does not respond, check the following: • The IAD-200 / IAD-200W is properly installed, LAN connectio

Common Connection Types Type Details ISP Data required Dynamic IP Address Your IP Address is allocated automatically, when you connect to you ISP.

Copyright Copyright (C) 2005 PLANET Technology Corp. All rights reserved. The products and programs described in this User’s Manual are licensed pro

Home Screen After finishing the Setup Wizard, you will see the Home screen. When you connect in future, you will see this screen when you connect. An

LAN Screen Use the LAN link on the main menu to reach the LAN screen. An example screen is shown below. Figure 6: LAN Screen Data - LAN Screen TCP/I

• The DHCP Server provides the Gateway and DNS addresses to the client, as well as allocating an IP Address. • The IAD-200 / IAD-200W can act as a

Wireless Screen (IAD-200W only) The IAD-200W's settings must match the other Wireless stations. Note that the IAD-200W will automatically accep

SSID This is also called the "Network Name". Enter the desired value. The default value is Wireless. • If using an ESS (Extended Service

Allow access by … Use this feature to determine which Wireless stations can use the Access Point. The options are: • All Wireless Stations - All wir

Wireless Security (IAD-200W only) This screen is accessed by clicking the "Configure" button on the Wireless screen. There are 3 options fo

Key Value Enter the key value or values you wish to use. The Default Key is required, the other keys are optional. Other stations must have the same

Trusted Wireless Stations (IAD-200W only) This feature can be used to prevent unknown Wireless stations from using the Access Point. This list has no

Edit Use this to change an existing entry in the "Trusted Stations" list: 1. Select the Station in the Trusted Station list. 2. Click the

Operation is subject to the Following two conditions: (1) This device may not cause harmful interference, and (2) This Device must accept any interfer

Password Screen The password screen allows you to assign a password to the IAD-200 / IAD-200W. Figure 11: Password Screen Old Password Enter the exi

4 Chapter 4 PC Configuration This Chapter details the PC Configuration required on the local ("Internal") LAN. Overview For each PC, the fo

Checking TCP/IP Settings - Windows 9x/ME: 1. Select Control Panel - Network. You should see a screen like the following: Figure 13: Network Configur

• On the Gateway tab, enter the IAD-200 / IAD-200W's IP address in the New Gateway field and click Add, as shown below. Your LAN administrator

Checking TCP/IP Settings - Windows NT4.0 1. Select Control Panel - Network, and, on the Protocols tab, select the TCP/IP protocol, as shown below. F

Figure 18: Windows NT4.0 - IP Address 3. Select the network card for your LAN. 4. Select the appropriate radio button - Obtain an IP address from

Figure 19 - Windows NT4.0 - Add Gateway 2. The DNS should be set to the address provided by your ISP, as follows: • Click the DNS tab. • On the D

Checking TCP/IP Settings - Windows 2000: 1. Select Control Panel - Network and Dial-up Connection. 2. Right - click the Local Area Connection icon a

5. Ensure your TCP/IP settings are correct, as described below. Using DHCP To use DHCP, select the radio button Obtain an IP Address automatically.

Checking TCP/IP Settings - Windows XP 1. Select Control Panel - Network Connection. 2. Right click the Local Area Connection and choose Properties.

Trademarks The PLANET logo is a trademark of PLANET Technology. This documenta-tion may refer to numerous hardware and software products by their tr

Figure 24: TCP/IP Properties (Windows XP) 5. Ensure your TCP/IP settings are correct. Using DHCP To use DHCP, select the radio button Obtain an IP

Internet Access To configure your PCs to use the IAD-200 / IAD-200W for Internet access: • Ensure that the Internet connection is functional. • Us

Macintosh Clients From your Macintosh, you can access the Internet via the IAD-200 / IAD-200W. The proce-dure is as follows. 1. Open the TCP/IP Cont

Wireless Station Configuration (IAD-200W only) This section applies to all Wireless stations wishing to use the IAD-200W's Access Point, regardl

Figure 26 Wireless Networks (Windows XP) If the "Broadcast SSID" setting on the IAD-200W has been disabled, its SSID will NOT be listed.

To connect: • Check the checkbox Allow me to connect to the selected wireless network, even though it is not secure. • The Connect button will then

Figure 29: Advanced - Wireless Networks Select the SSID for the IAD-200W, and click Configure, to see a screen like the following: Figure 30: Wirel

• For the Network key and Confirm network key, enter the default key value used on the IAD-200W. (Windows will determine if 64bit or 128bit encrypti

If using WPA-PSK Data Encryption (IAD-200W only) If WPA-PSK data encryption has been enabled on the IAD-200W, it does not matter which network is sel

Figure 34: Wireless Network Properties- WPA-PSK Configure this screen as follows: • Set Network Authentication to WPA-PSK. • For Data Encryption,

Table of Contents CHAPTER 1 INTRODUCTION...1 IAD-200 / IAD-200W Features ...

Figure 35: Preferred Networks Click OK to establish a connection to the IAD-200W. If the SSID is not listed (IAD-200W only) If the "Broadcast

Figure 37: Unlisted Wireless Network 2. Click the Add button. You will see a screen like the example below. Figure 38: Add Wireless Network 3. Con

• If using data encryption (WEP or WPA-PSK), enter the key used on the IAD-200W. See the preceding sections for details of WEP and WPA-PSK. • Unche

5 Chapter 5 Advanced Features This Chapter explains when and how to use the IAD-200 / IAD-200W's "Advanced" Features. Overview The fol

DMZ This feature, if enabled, allows the DMZ computer on your LAN to be exposed to all users on the Internet. • This allows almost any application

Data - Special Applications Screen Checkbox Use this to Enable or Disable this Special Application as required. Name Enter a descriptive name to iden

Figure 42: URL Filter Screen Data - URL Filter Screen Current Filter Strings Current Filter Strings The list contains the current list of items to b

Trusted PC Allow Trusted PC Enable this to allow one computer to have unrestricted access to the Internet. For this PC, the URL filter will be ignore

Dynamic DNS (Domain Name Server) This free service is very useful when combined with the Virtual Server feature. It allows Internet users to connect

DDNS Data Host Name Enter the domain name allocated to you by the DDNS Service. If you have more than one name, enter the name you wish to use. User

Routing...85 Upgrade Firmware...

Firewall Rules The Firewall Rules screen allows you to define "Firewall Rules" which can allow or prevent certain traffic. "Traffic&qu

Action The action performed on connections which are covered by this rule. LAN Server The PC or Server on your LAN to which traffic covered by this r

Incoming Rules (Inbound Services) This screen is displayed when the "Add" or "Edit" button for Incoming Rules is clicked. Figure

Log This determines whether packets covered by this rule are logged. Select the desired action. • Always - always log traffic considered by this ru

BLOCK rule. (That is, you wish to allow a subset of traffic which is currently blocked by another rule.) • To define the Schedule used in these sel

User-defined Services Services are used when creating Firewall Rules. If you wish to create a firewall rule, but the required service is not listed

Add/Edit Service This screen is displayed when the Add or Edit button on the Services screen is clicked. Figure 48 : Add/Edit Service Data - Add/Edi

Options This screen allows advanced users to enter or change a number of settings. For normal opera-tion, there is no need to use this screen or chan

Schedule This Schedule can be used for the Firewall Rules and the URL filter. Figure 50: Schedule Screen Data - Schedule Screen Schedule Day Each d

light Savings Time adjustment period, and uncheck it at the end of the Daylight Savings period. Use this NTP Server If you prefer to use a particular

1 Chapter 1 Introduction This Chapter provides an overview of the ADSL 2/2+ VoIP router (IAD-200) / 802.11g ADSL 2/2+ VoIP router's (IAD-200W) f

Virtual Servers This feature, sometimes called Port Forwarding, allows you to make Servers on your LAN accessible to Internet users. Normally, Intern

• To make it easier for Internet users to connect to your Servers, you can use the "DDNS" feature. This allows Internet users to connect t

Note: From the Internet, ALL Virtual Servers have the IP Address allocated by your ISP. 66

VoIP To use the VoIP feature requires the following: • Standard Phone A standard analogue Phone must be connected to the Phone socket. • VoIP (SIP

Figure 53: VoIP Settings VoIP Settings Local Service SIP Local Port This port is used for peer-to-peer (direct) connections to another device, when

SIP register port Enter the port used for "Register" connections to the Server above. Register Expiry Time This sets the "Idle Timeou

Display Name This is the name you chose when you first opened your account. Your "Display Name" will be visible to other individuals with c

PSTN Settings PSTN Relay PSTN Prefix The PSTN Relay allows certain calls to be diverted to the PSTN link, even though VoIP is working properly. This

6 Chapter 6 Advanced Administration This Chapter explains the settings available via the "Administration" section of the menu. Overview Nor

PC Database The PC Database is used whenever you need to select a PC (e.g. for the "DMZ" PC). • It eliminates the need to enter IP addres

• Auto-detection of Internet Connection Method. In must situations, the IAD-200 / IAD-200W can test your ADSL and Internet connection to determine t

Data - PC Database Screen Known PCs This lists all current entries. Data displayed is name (IP Address) type. The "type" indicates whether

PC Database - Advanced This screen is displayed if the "Advanced Administration" button on the PC Database is clicked. It provides more con

IP Address Select the appropriate option: • Automatic - The PC is set to be a DHCP client (Windows: "Ob-tain an IP address automatically")

Config File This feature allows you to download the current settings from the IAD-200 / IAD-200W, and save them to a file on your PC. You can restore

Logs The Logs record various types of activity on the IAD-200 / IAD-200W. This data is useful for troubleshooting, but enabling all logs will generat

Buttons There are three (3) buttons • Refresh - Update the log data. • Clear Log - Clear the log, and restart it. This makes new messages easier to

E-mail This screen allows you to E-mail Logs and Alerts. A sample screen is shown below. Figure 60: E-mail Screen Data - E-mail Screen E-Mail Notif

Password If you have enabled "My SMTP Mail Server requires authentication" above, enter the password required to login to your SMTP Server.

Diagnostics This screen allows you to perform a "Ping" or a "DNS lookup". These activities can be useful in solving network probl

Remote Administration If enabled, this feature allows you to manage the IAD-200 / IAD-200W via the Internet. Figure 62: Remote Administration Sc

• WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key sizes of 64 Bit and 128 Bit are supported. WEP encrypts any data before t

For security, you should restrict access to as few external IP ad-dresses as practical. To connect from a remote PC via the Internet 1. Ensure your

Routing Overview • If you don't have other Routers or Gateways on your LAN, you can ignore the "Routing" page completely. • If the

Figure 63: Routing Screen Data - Routing Screen RIP RIP Direction Select the desired RIP Direction. RIP Version Choose the RIP Version for the Serv

Local Router The local router is the Router installed on the same LAN segment as the IAD-200 / IAD-200W. This router requires that the Default Route

Router) Metric 2 Entry 2 (Segment 2) Destination IP Address 192.168.2.0 Network Mask 255.255.255.0 (Standard Class C) Gateway IP Address 192.168.

Upgrade Firmware The firmware (software) in the IAD-200 / IAD-200W can be upgraded using your Web Browser. You must first download the upgrade file,

7 Chapter 7 Operation and Status This Chapter details the operation of the IAD-200 / IAD-200W and the status screens. Operation Once both the IAD-200

Figure 66: Status Screen Data - Status Screen System Device Name The current name of the Router. This name is also the "hostname" for use

Internet (VC1) Connection Method Displays the current connection method, as set in the Setup Wizard. Connection Status This indicates the current sta

devices currently on the network. Refresh Screen Update the data displayed on screen. 93